|
6 E |
Maintains wear and corrosion resistance properties at elevated temperatures. |
AWS ECoCr-A |
42-46 Rc as welded |
Data Sheet
|
|
21 E |
For overlays subjected to heat and impact at high temperatures. Weld metal also provides good crack resistance. |
Co-Cr-Mo |
28-33 Rc as welded |
Data Sheet
|
|
2101 E |
Offers superior resistance to heat checking, spalling, chipping and erosion over our 21 alloy |
Co-Cr-Mo-Cb |
33-38 Rc as welded
45+ Rc work hardened |
Data Sheet
|
|
4130 E |
Responds to 4130 quench and temper. Used as a flame hardening alloy. |
AISI 4130 type |
Flame hardens to Rc |
|
|
4130LN E |
Modified 4130 with a less than 1% Nickel to improve resistance cracking. Welds 4130 and 4140 alloys. |
AISI 4130 modified |
Heat Treatable |
Data Sheet
|
|
4140 E |
Responds to 4140 quench and temper. Used as a flame hardening tool. |
AISI 4140 type |
Flame hardens to 56 Rc |
|
|
4340 E |
Used for the repair of 4340 base metal. |
AISI 4340 type |
Heat Treatable |
|
|
F15 E |
A very tough alloy for use in the repair of columns and cylinders and other areas subject to cracking. |
Fe-Ni-Cr-Mo 6% alloy |
15-20 Rc as welded
115,000 psi tensile |
Data Sheet
|
|
F25 E |
This alloy is used to buildup worn areas subject to high impact and compressive loads such as rams, sow blocks and shanks. |
Fe-Ni-Cr-Mo 8% alloy |
25-30 Rc as welded
132,000 psi tensile |
Data Sheet
|
|
F35 E |
For reclamation of hammer die impressions. This alloy is similar in wear properties to die block with a number 2 temper. |
Fe-Ni-Cr-Mo 10% alloy |
32-37 Rc as welded
165,000 psi tensile |
Data Sheet
|
|
F40 E |
For hammer die impressions when more abrasion resistance is needed than F35 FC provides. |
Fe-Ni-Cr-Mo 12% alloy |
38-43 Rc as welded
182,000 psi tensile |
Data Sheet
|
|
F45 E |
For shallow hammer and press die impressions. |
Fe-Ni-Cr-Mo 14% alloy |
42-47 Rc as welded
186,000 psi tensile |
Data Sheet
|
|
F54 E |
Provides machinable deposit for press die applications. |
5% Cr Hot Work |
38-42 Rc as welded |
Data Sheet
|
|
F58 E |
A 5% Cr hot work alloy for press dies. |
AISI H-12 |
51-56 Rc as welded |
Data Sheet
|
|
F63 E |
For shallow hammer dies with high duty cycles and press dies subjected to high heat and stresses when a machinable deposit is required. |
9% Cr Hot Work |
42-46 Rc as welded |
Data Sheet
|
|
F64 E |
For use on press dies subjected to high heat and stresses. |
11% Cr Hot Work |
48-53 Rc as welded |
Data Sheet
|
|
F65 E |
For shallow hammer dies with high duty cycles and press dies subjected to high heat and stresses. |
9.5% Cr Hot Work |
49-52 Rc as welded |
Data Sheet
|
|
F110 E |
Used for overlaying of forging dies and components subject to high temperatures and impacts. |
AWS ENiCrMo-5 |
100,000 psi tensile min.
20 Rc as welded |
Data Sheet
|
|
F111 E |
An excellent underlayment for harder nickel base alloys on high temperature forging dies. |
Modification of AWS ENiCrMo-5 |
20 Rc as welded
40 Rc workhardened |
Data Sheet
|
|
F112 E |
For forging surfaces exposed to high temperatures and long contact times. |
Modification of AWS ENiCrMo-3 |
110,000 psi tensile
30% Elongation min. |
Data Sheet
|
|
F580 E |
A higher alloy version of F58 that withstands higher service temperatures without softening. |
AISI H-12 type with higher W and MO |
52-57 Rc as welded |
Data Sheet
|